Commercial Roof Coating Systems

★★★★★ 4.91,400+ Google reviews20,000+ roofs replaced

Serving Texas & Louisiana Since 1983

Commercial roof coatings are fluid-applied membranes used to restore and protect qualifying existing roofs. A successful coating system needs a serviceable roof assembly, a compatible substrate, corrected defects, thorough preparation and a coating chosen for the roof's drainage, exposure and performance needs.

Licensed, insured & bonded

Get a Free Commercial Assessment

No cost, no obligation. We will contact you to schedule.

Step 1 of 2 - How Should We Contact You?

This field is for validation purposes and should be left unchanged.
First Name
Last Name

Free assessment · No obligation · Serving Texas & Louisiana since 1983

Privacy Policy · Terms & Conditions

GAF President's Club

GAF Master Elite

Google 4.9-star rating, 1,400+ reviews

Angi Super Service Award

BBB Accredited A+ Rating

Is your roof a candidate for coating?

Coating works on roofs that are worn but still sound. These are the conditions we look for, and the ones that rule it out. Not every roof qualifies, so every coating project starts with an assessment. A coating restores a sound roof; it does not hide a failing one.

A roof may qualify when

  • The roof assembly remains structurally serviceable
  • Moisture is limited and identifiable
  • The substrate is compatible with an approved coating system
  • Drainage is adequate or can be corrected
  • Seams, penetrations and isolated defects can be repaired
  • Existing materials remain sufficiently adhered
  • The roof can be cleaned and prepared to manufacturer requirements
  • Restoration is economically reasonable relative to replacement

Coating may not be appropriate when

  • Wet insulation or trapped moisture is widespread
  • Decking or structural components are compromised
  • The membrane has extensive adhesion failure
  • Drainage or ponding cannot be corrected
  • Deterioration is widespread
  • Contamination prevents reliable adhesion
  • Repeated repairs point to systemic failure
  • The roof is past the point of economical restoration

01

Assess condition

Review the existing assembly, reported problems and previous repairs.

02

Test compatibility

Check moisture, adhesion and compatibility with an approved coating system.

03

Correct defects

Repair seams, penetrations and isolated damage first.

04

Prepare surface

Clean the roof and apply the primers or treatments the system requires.

05

Apply coating

Apply reinforcement and coating to the specified requirements.

Honest note: A coating should never be used to conceal unresolved damage. If a step fails, we stop and tell you why.

Compatible commercial roof systems

Compatibility depends on the product and the roof's condition. These are the existing roofs we evaluate for coating.

TPO roofing

TPO and PVC

Cleaning, adhesion testing, seam condition, previous repairs and manufacturer-approved primers or preparation.

Modified bitumen

Modified bitumen

Surface condition, granule loss, bleed-through, existing repairs and compatible primers.

Metal roofing

Commercial metal

Rust treatment, fasteners, seams, penetrations, panel movement and reinforcement.

Roof coatings

Existing coated roofs

Identifying the current coating, testing adhesion and compatibility, and deciding whether recoating is appropriate.

Where a coating system needs extra detail: the field is the easy part, and leaks start at transitions. Field membrane, seams, penetrations, HVAC curbs, drains and scuppers, parapet transitions, metal-roof fasteners and high-traffic areas get repairs and reinforcement before the field coat.

Compare commercial roof-coating types

No single coating is best. The right one depends on drainage, foot traffic, the substrate and how you plan to recoat later.

CoatingCommon strengthsImportant considerationsPotential applications
SiliconeStrong UV and weather resistance; often considered where water exposure is a concernCan attract dirt, may be slippery and needs compatible recoat productsQualifying low-slope commercial roofs
AcrylicReflective, widely available and typically easy to apply or recoatSensitive to weather during application and to persistent pondingRoofs with positive drainage
PolyurethaneStrong abrasion and impact resistance; useful in high-traffic areasProduct selection, odor and application requirements varyService paths and roofs exposed to traffic or impact
Hybrid systemsCombine materials or reinforcement for specific conditionsMust be designed and installed as one compatible systemProject-specific restoration assemblies

What "elastomeric" means: It describes a coating's ability to stretch and recover. It is not a separate material; acrylic, silicone and polyurethane products can all be sold as elastomeric.

Benefits and limits of roof coatings

Potential benefits

  • Restore a qualifying roof without a full tear-off
  • Create a continuous protective surface
  • Reinforce repaired seams and penetrations
  • Improve reflectivity with qualifying products
  • Reduce demolition waste
  • Less disruption than some replacement projects
  • A renewable restoration path where appropriate
  • Support planned lifecycle budgeting

Important limitations

  • Coatings do not correct structural problems
  • They do not remove wet insulation
  • They cannot make up for poor drainage indefinitely
  • Performance depends heavily on preparation and application
  • Not every roof or substrate qualifies
  • Warranty requirements vary by manufacturer and system
  • Periodic inspection and maintenance are still needed
  • A coating cannot make a failing roof permanently serviceable

Coat, repair or replace?

The condition of the roof decides, not the price of the cheapest option.

Existing conditionLikely direction
Small isolated defect on an otherwise serviceable roofTargeted repair
Serviceable roof with correctable defects and a compatible substrateCoating / restoration evaluation
Localized wet areas in an otherwise viable assemblyRepair those areas, then reassess restoration
Widespread trapped moisture or adhesion failureReplacement evaluation
Compromised decking or structural concernsCorrect structure, evaluate replacement
Roof near failure after repeated unsuccessful repairsReplacement may be more responsible
Existing coating still in serviceable conditionRecoat assessment may be appropriate

How we do the work

M&M's roof-coating and restoration process

Most of the work happens before any coating goes down. Prep, not spray.

01

Assessment and testing

Identify the existing assembly, reported problems, previous repairs and your restoration goals, and decide whether moisture testing, core samples or adhesion tests are needed.

02

Scope development

Document repairs, preparation, coating system, reinforcement and application requirements.

03

Repairs and detailing

Correct eligible defects at seams, penetrations, flashings, drains and damaged areas.

04

Cleaning and preparation

Clean the surface and apply primers or treatments the approved system requires.

05

Coating application

Apply reinforcement and coating at the specified coverage rate and thickness.

06

Quality review and documentation

Inspect the work, document the application and hand over warranty and maintenance information.

What the building owner receives

Each coating project ends with a record you can hand to an asset manager, insurer or the next contractor.

Condition and scope

What we found and what we did.

  • Existing roof and substrate identification
  • Roof-condition photographs
  • Repairs and preparation requirements
  • Completed scope

Coating system

What went on the roof.

  • Coating type and manufacturer
  • Reinforcement details
  • Target coverage rate or thickness
  • Before, during and after photos

Handover

What keeps the roof performing.

  • Warranty documentation
  • Maintenance and inspection recommendations
  • Areas excluded from the coating scope

Performance, warranty and maintenance

A coated roof still needs care. Here is what keeps it performing and its warranty valid.

During installation

Manufacturer preparation and primer requirements, documented coverage rate or dry-film thickness, and weather windows and cure time.

Ongoing maintenance

Inspection after major weather events, clear drains, scuppers and debris, repair of damage left by other trades, periodic condition reviews and a recoat evaluation near the end of the coating term.

Three kinds of warranty

Product warranty covers the coating material itself. Manufacturer system warranty covers the installed system, often with inspection and thickness requirements. Workmanship is M&M's coverage for how the work was installed.

A warranty term is not a roof life

Coverage depends on the specific product, installed thickness, preparation, application and manufacturer inspection. It does not guarantee the roof lasts that long.

We're trusted by our clients

★ 4.9 average · 1,400+ Google reviews

Jacob Kempnich
Jacob Kempnich
★★★★★
We just had our roof replaced by M&M Roofing in Clearlake and were very pleased with their work. Michael McCollom did a great job of explaining everything to us beforehand, including discussing options and plans, the pricing and scope was very fair and reasonable. Once we signed the contract for the work, he communicated with us promptly about dates and expectations. The crew showed up and they were extremely fast and efficient. The roof looks great, and we couldn't be happier. We highly recommend M&M Roofing Siding & Windows.
Steve Hargis
Steve Hargis
★★★★★
We had M&M come out to repair a couple of leaks in our covered patio. Greg was super helpful in diagnosing the issues, providing lots of information on how best to make the repairs and options for what we needed.


The work was completed in one day and Greg came out to make sure the crew was doing everything the way he wanted. The whole process was really great. Very professional from start to finish. Thanks M&M.
Cassandra Lazos
Cassandra Lazos
★★★★★
I recently had the pleasure of working with M&M for siding work on my house, and I must say, the experience exceeded all my expectations. From the get-go, the level of customer service was simply outstanding. A special shoutout to Sam, our representative, who was not only professional and knowledgeable but also incredibly attentive to our needs.

Sam went above and beyond to ensure that all our questions were answered, and our concerns addressed, making the entire process smooth and stress-free.
Rachel Maddoux
Rachel Maddoux
★★★★★
Tim did a great job. He picked out tile that exactly matched my roof. I only had to replace a portion of …
Brittney Richard
Brittney Richard
★★★★★
I cannot say enough good things about this roofing company! From start to finish, the entire experien…
Sam Trujillo
Sam Trujillo
★★★★★
Chris P. was prompt and knowledgeable about his product and shared wonderful insight as t…
Keith Blackford
Keith Blackford
★★★★★
Honest, professional, easy to deal with! Highly recommend.
Bill G
Bill G
★★★★★
Replaced our mid-1980s residential siding with a major-branded cement-fiber product in August…
Charlotte Childress
Charlotte Childress
★★★★★
M&M has been there for me through a new roof, siding, and gutters… they are professionals th…
Jingting Yang
Jingting Yang
★★★★★
We recently replaced our 20-year-old roof using M&M Roofing, and we couldn’t be happier with our…

Commercial roof-coating FAQs

A fluid-applied membrane installed over a qualifying existing roof to restore and protect it. As a system, it includes repairs, preparation, primers or reinforcement where required, and the coating itself applied at a specified thickness.

Generally, the roof must be structurally sound, mostly dry, compatible with an approved coating and able to drain. Whether your roof meets that takes an on-site assessment, often with moisture and adhesion testing.

Silicone is commonly chosen for UV and water exposure but needs compatible products to recoat. Acrylic is reflective and easy to recoat but is more sensitive to ponding and application weather. The right one depends on your roof's drainage and use.

Not on its own. Leaks are located and repaired first, and any wet insulation is addressed. The coating then protects the repaired roof. Coating over an active leak can hide the problem rather than solve it.

Often, if the existing roof is in suitable condition and the coating is approved for that substrate. Each needs different preparation: cleaning and primers on TPO, granule and bleed-through checks on modified bitumen, rust and fastener treatment on metal.

It depends on the product, installed thickness, preparation, exposure and maintenance. Manufacturer warranty terms vary by system, but a warranty term is not a guaranteed lifespan. We will explain what applies to the system we recommend.

Often, yes, if the existing coating is still adhered and serviceable and the new product is compatible. A recoat evaluation near the end of the coating term tells you whether that is an option.

Usually it involves less demolition and noise than a tear-off, but it is not zero-disruption. Odor, rooftop access, weather windows and cure time still need planning around your operations.

Find out whether your roof qualifies

Tell us about the building. We will assess the roof, test where needed and tell you whether coating, repair or replacement makes sense. The answer comes after the assessment, not before.

★ 4.91,400+ Google reviews20,000+ roofs replaced