Commercial Roof Coating Systems
★★★★★ 4.9·1,400+ Google reviews·20,000+ roofs replaced
Serving Texas & Louisiana Since 1983
Commercial roof coatings are fluid-applied membranes used to restore and protect qualifying existing roofs. A successful coating system needs a serviceable roof assembly, a compatible substrate, corrected defects, thorough preparation and a coating chosen for the roof's drainage, exposure and performance needs.
Licensed, insured & bonded
Get a Free Commercial Assessment
No cost, no obligation. We will contact you to schedule.
Free assessment · No obligation · Serving Texas & Louisiana since 1983
GAF President's Club
GAF Master Elite
Google 4.9-star rating, 1,400+ reviews
Angi Super Service Award
BBB Accredited A+ Rating
Is your roof a candidate for coating?
Coating works on roofs that are worn but still sound. These are the conditions we look for, and the ones that rule it out. Not every roof qualifies, so every coating project starts with an assessment. A coating restores a sound roof; it does not hide a failing one.
A roof may qualify when
- The roof assembly remains structurally serviceable
- Moisture is limited and identifiable
- The substrate is compatible with an approved coating system
- Drainage is adequate or can be corrected
- Seams, penetrations and isolated defects can be repaired
- Existing materials remain sufficiently adhered
- The roof can be cleaned and prepared to manufacturer requirements
- Restoration is economically reasonable relative to replacement
Coating may not be appropriate when
- Wet insulation or trapped moisture is widespread
- Decking or structural components are compromised
- The membrane has extensive adhesion failure
- Drainage or ponding cannot be corrected
- Deterioration is widespread
- Contamination prevents reliable adhesion
- Repeated repairs point to systemic failure
- The roof is past the point of economical restoration
01
Assess condition
Review the existing assembly, reported problems and previous repairs.
02
Test compatibility
Check moisture, adhesion and compatibility with an approved coating system.
03
Correct defects
Repair seams, penetrations and isolated damage first.
04
Prepare surface
Clean the roof and apply the primers or treatments the system requires.
05
Apply coating
Apply reinforcement and coating to the specified requirements.
Honest note: A coating should never be used to conceal unresolved damage. If a step fails, we stop and tell you why.
Compatible commercial roof systems
Compatibility depends on the product and the roof's condition. These are the existing roofs we evaluate for coating.
TPO and PVC
Cleaning, adhesion testing, seam condition, previous repairs and manufacturer-approved primers or preparation.
Modified bitumen
Surface condition, granule loss, bleed-through, existing repairs and compatible primers.
Commercial metal
Rust treatment, fasteners, seams, penetrations, panel movement and reinforcement.
Existing coated roofs
Identifying the current coating, testing adhesion and compatibility, and deciding whether recoating is appropriate.
Where a coating system needs extra detail: the field is the easy part, and leaks start at transitions. Field membrane, seams, penetrations, HVAC curbs, drains and scuppers, parapet transitions, metal-roof fasteners and high-traffic areas get repairs and reinforcement before the field coat.
Compare commercial roof-coating types
No single coating is best. The right one depends on drainage, foot traffic, the substrate and how you plan to recoat later.
| Coating | Common strengths | Important considerations | Potential applications |
|---|---|---|---|
| Silicone | Strong UV and weather resistance; often considered where water exposure is a concern | Can attract dirt, may be slippery and needs compatible recoat products | Qualifying low-slope commercial roofs |
| Acrylic | Reflective, widely available and typically easy to apply or recoat | Sensitive to weather during application and to persistent ponding | Roofs with positive drainage |
| Polyurethane | Strong abrasion and impact resistance; useful in high-traffic areas | Product selection, odor and application requirements vary | Service paths and roofs exposed to traffic or impact |
| Hybrid systems | Combine materials or reinforcement for specific conditions | Must be designed and installed as one compatible system | Project-specific restoration assemblies |
What "elastomeric" means: It describes a coating's ability to stretch and recover. It is not a separate material; acrylic, silicone and polyurethane products can all be sold as elastomeric.
Benefits and limits of roof coatings
Potential benefits
- Restore a qualifying roof without a full tear-off
- Create a continuous protective surface
- Reinforce repaired seams and penetrations
- Improve reflectivity with qualifying products
- Reduce demolition waste
- Less disruption than some replacement projects
- A renewable restoration path where appropriate
- Support planned lifecycle budgeting
Important limitations
- Coatings do not correct structural problems
- They do not remove wet insulation
- They cannot make up for poor drainage indefinitely
- Performance depends heavily on preparation and application
- Not every roof or substrate qualifies
- Warranty requirements vary by manufacturer and system
- Periodic inspection and maintenance are still needed
- A coating cannot make a failing roof permanently serviceable
Coat, repair or replace?
The condition of the roof decides, not the price of the cheapest option.
| Existing condition | Likely direction |
|---|---|
| Small isolated defect on an otherwise serviceable roof | Targeted repair |
| Serviceable roof with correctable defects and a compatible substrate | Coating / restoration evaluation |
| Localized wet areas in an otherwise viable assembly | Repair those areas, then reassess restoration |
| Widespread trapped moisture or adhesion failure | Replacement evaluation |
| Compromised decking or structural concerns | Correct structure, evaluate replacement |
| Roof near failure after repeated unsuccessful repairs | Replacement may be more responsible |
| Existing coating still in serviceable condition | Recoat assessment may be appropriate |
How we do the work
Commercial roof repair
Diagnosis and targeted repair of leaks, seams and failed details across commercial systems.
Commercial roof replacement
When moisture, adhesion failure or repeated repairs point past restoration.
Commercial roofing
Inspection, maintenance, restoration and the full range of commercial roofing services.
M&M's roof-coating and restoration process
Most of the work happens before any coating goes down. Prep, not spray.
01
Assessment and testing
Identify the existing assembly, reported problems, previous repairs and your restoration goals, and decide whether moisture testing, core samples or adhesion tests are needed.
02
Scope development
Document repairs, preparation, coating system, reinforcement and application requirements.
03
Repairs and detailing
Correct eligible defects at seams, penetrations, flashings, drains and damaged areas.
04
Cleaning and preparation
Clean the surface and apply primers or treatments the approved system requires.
05
Coating application
Apply reinforcement and coating at the specified coverage rate and thickness.
06
Quality review and documentation
Inspect the work, document the application and hand over warranty and maintenance information.
What the building owner receives
Each coating project ends with a record you can hand to an asset manager, insurer or the next contractor.
Condition and scope
What we found and what we did.
- Existing roof and substrate identification
- Roof-condition photographs
- Repairs and preparation requirements
- Completed scope
Coating system
What went on the roof.
- Coating type and manufacturer
- Reinforcement details
- Target coverage rate or thickness
- Before, during and after photos
Handover
What keeps the roof performing.
- Warranty documentation
- Maintenance and inspection recommendations
- Areas excluded from the coating scope
Performance, warranty and maintenance
A coated roof still needs care. Here is what keeps it performing and its warranty valid.
During installation
Manufacturer preparation and primer requirements, documented coverage rate or dry-film thickness, and weather windows and cure time.
Ongoing maintenance
Inspection after major weather events, clear drains, scuppers and debris, repair of damage left by other trades, periodic condition reviews and a recoat evaluation near the end of the coating term.
Three kinds of warranty
Product warranty covers the coating material itself. Manufacturer system warranty covers the installed system, often with inspection and thickness requirements. Workmanship is M&M's coverage for how the work was installed.
A warranty term is not a roof life
Coverage depends on the specific product, installed thickness, preparation, application and manufacturer inspection. It does not guarantee the roof lasts that long.
We're trusted by our clients
★ 4.9 average · 1,400+ Google reviews
The work was completed in one day and Greg came out to make sure the crew was doing everything the way he wanted. The whole process was really great. Very professional from start to finish. Thanks M&M.
Sam went above and beyond to ensure that all our questions were answered, and our concerns addressed, making the entire process smooth and stress-free.
Six offices across Texas & Louisiana
Wherever you are in our service area, an M&M office is never far away.
Commercial roof-coating FAQs
What is a commercial roof coating?
A fluid-applied membrane installed over a qualifying existing roof to restore and protect it. As a system, it includes repairs, preparation, primers or reinforcement where required, and the coating itself applied at a specified thickness.
How do I know whether my roof can be coated?
Generally, the roof must be structurally sound, mostly dry, compatible with an approved coating and able to drain. Whether your roof meets that takes an on-site assessment, often with moisture and adhesion testing.
What is the difference between silicone and acrylic roof coatings?
Silicone is commonly chosen for UV and water exposure but needs compatible products to recoat. Acrylic is reflective and easy to recoat but is more sensitive to ponding and application weather. The right one depends on your roof's drainage and use.
Can a coating stop an active roof leak?
Not on its own. Leaks are located and repaired first, and any wet insulation is addressed. The coating then protects the repaired roof. Coating over an active leak can hide the problem rather than solve it.
Can TPO, modified bitumen or metal roofs be coated?
Often, if the existing roof is in suitable condition and the coating is approved for that substrate. Each needs different preparation: cleaning and primers on TPO, granule and bleed-through checks on modified bitumen, rust and fastener treatment on metal.
How long does a commercial roof coating last?
It depends on the product, installed thickness, preparation, exposure and maintenance. Manufacturer warranty terms vary by system, but a warranty term is not a guaranteed lifespan. We will explain what applies to the system we recommend.
Can a coated roof be recoated later?
Often, yes, if the existing coating is still adhered and serviceable and the new product is compatible. A recoat evaluation near the end of the coating term tells you whether that is an option.
Is roof coating less disruptive than replacement?
Usually it involves less demolition and noise than a tear-off, but it is not zero-disruption. Odor, rooftop access, weather windows and cure time still need planning around your operations.
Find out whether your roof qualifies
Tell us about the building. We will assess the roof, test where needed and tell you whether coating, repair or replacement makes sense. The answer comes after the assessment, not before.
★ 4.91,400+ Google reviews20,000+ roofs replaced